Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
Listed here in the next paragraph you'll find a bunch of superb content about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
![A Step-by-Step Guide to Installing a Bathtub](https://st.hzcdn.com/fimgs/12c246da01389649_2990-w500-h666-b0-p0--.jpg)
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the task can relocate easily; if you have to open up a wall to remove the old bathtub and also place the new bathtub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub and also set in the brand-new one. Ensure you have actually certified yourself for the job as well as are comfortable trying it. Instead of working with a service provider to take control of a halfway-completed job, it is much better to think about using one prior to you begin. Possibilities are you may require an expert plumber to make tube links.
This write-up will certainly assist you set up a brand-new bathtub in your restroom if you have actually currently bought a brand-new bathtub as well as don't require to change the arrangement of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any water staying in the system. The process of eliminating the existing taps can be fairly bothersome due to the limited access that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. Once the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Protect the faucet in place with the supplier given backnut. Once the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Tub
Utilizing the two wood boards under its feet, place the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Turn on the supply of water and check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bath tub must wait till the bathtub has been utilized at the very least when as this will certainly settle it into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to permeate the wall between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the bath tub with water before sealing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break fairly early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![How to Install a Bathtub](http://cdn.shopify.com/s/files/1/0419/8344/3097/products/4_0ba0e4d6-fd1f-487b-8ab2-ad7da4fccf86_1200x1200.jpg?v=1612603835)
As an enthusiastic person who reads about Tools You Need to Install a New Bathtub , I thought sharing that segment was a good idea. Enjoyed our review? Please share it. Let someone else find it. Thanks so much for taking the time to read it.
Act immediately. Report this page